- English
- Español
- Português
- русский
- Français
- 日本語
- Deutsch
- tiếng Việt
- Italiano
- Nederlands
- ภาษาไทย
- Polski
- 한국어
- Svenska
- magyar
- Malay
- বাংলা ভাষার
- Dansk
- Suomi
- हिन्दी
- Pilipino
- Türkçe
- Gaeilge
- العربية
- Indonesia
- Norsk
- تمل
- český
- ελληνικά
- український
- Javanese
- فارسی
- தமிழ்
- తెలుగు
- नेपाली
- Burmese
- български
- ລາວ
- Latine
- Қазақша
- Euskal
- Azərbaycan
- Slovenský jazyk
- Македонски
- Lietuvos
- Eesti Keel
- Română
- Slovenski
- मराठी
- Srpski језик
How to use spinning reel？
2022-09-28
1. Winding method
① Check the winding amount of the reel (generally marked on the reel or the packing box) and select the appropriate fishing line model.
② Install the fishing reel on the fishing rod and turn off the fishing reel backstop switch.
③ Knot one end of the line, pass through a fishing rod's guide ring, open the fishing reel's outlet ring, tie the line to the reel, and close the outlet ring. Pull the fishing line to check and ensure that it is fastened firm.
④ Keep the fishing line straight and tight and start turning the reel rocker at a constant speed to wind the line.
⑤ When the line is about 1.5-2 mm below the edge of the reel, keep the line straight and tight, stop winding, cut the line and pin it to the spool's spinner.
2. Install method
① Install the fishing reel on the fishing rod.
② Turn on the fishing reel backstop switch, open the fishing reel outlet ring, pull out the line, close the outlet ring, and pass the line through the fishing rod guide ring in turn.
③ Fasten the falling line, tighten the sections of the fishing rod, and close the fishing reel backstop switch.
3. Throwing method
① Turn on the backstop switch of the fishing reel, turn the rocker, adjust the line to fall to the proper position, and turn off the backstop switch.
② Hook the line with your index finger, turn your head sideways and send the rod back as far as the line drop touches the ground.
③ Send the rod side up and forward, when the rod is in front of the side and the ground is held at a 45-degree angle, shake the line loose and eject the line drop.
④ When the line falls into the water after the line feeding is completed, shake the rocker, close the line ring, tighten the fishing line, and put the rod on the rod frame.
① Lift the rod, shake it, keep the fishing line tight and straight, and place the rod at a 45-degree angle to the ground.
② Shake the reel at a constant speed, keep the fishing line tight and straight, and adjust the tightness knob of the fishing wheel according to the size of the fishing force.
③ After the fish is collected, put the rod on the rack, and the fishing reel should not touch the ground and get dirty and scratched.
5. Unloading method
① Turn off the backstop switch and remove the line drop.
② Tighten the line with your fingers and shake the joystick.
③ Attaching the thread to the spool disc
④ Unload the reel, clean it, and install it.
6. Maintenance
① After each fishing, the reel should be cleaned and dried.
② Regular (25 fishing trips) dismantling for maintenance, greasing of tooth discs, screw teeth, positioning teeth, sliders, rocker shafts, bearings, etc.
① Check the winding amount of the reel (generally marked on the reel or the packing box) and select the appropriate fishing line model.
② Install the fishing reel on the fishing rod and turn off the fishing reel backstop switch.
③ Knot one end of the line, pass through a fishing rod's guide ring, open the fishing reel's outlet ring, tie the line to the reel, and close the outlet ring. Pull the fishing line to check and ensure that it is fastened firm.
④ Keep the fishing line straight and tight and start turning the reel rocker at a constant speed to wind the line.
⑤ When the line is about 1.5-2 mm below the edge of the reel, keep the line straight and tight, stop winding, cut the line and pin it to the spool's spinner.
2. Install method
① Install the fishing reel on the fishing rod.
② Turn on the fishing reel backstop switch, open the fishing reel outlet ring, pull out the line, close the outlet ring, and pass the line through the fishing rod guide ring in turn.
③ Fasten the falling line, tighten the sections of the fishing rod, and close the fishing reel backstop switch.
3. Throwing method
① Turn on the backstop switch of the fishing reel, turn the rocker, adjust the line to fall to the proper position, and turn off the backstop switch.
② Hook the line with your index finger, turn your head sideways and send the rod back as far as the line drop touches the ground.
③ Send the rod side up and forward, when the rod is in front of the side and the ground is held at a 45-degree angle, shake the line loose and eject the line drop.
④ When the line falls into the water after the line feeding is completed, shake the rocker, close the line ring, tighten the fishing line, and put the rod on the rod frame.
① Lift the rod, shake it, keep the fishing line tight and straight, and place the rod at a 45-degree angle to the ground.
② Shake the reel at a constant speed, keep the fishing line tight and straight, and adjust the tightness knob of the fishing wheel according to the size of the fishing force.
③ After the fish is collected, put the rod on the rack, and the fishing reel should not touch the ground and get dirty and scratched.
5. Unloading method
① Turn off the backstop switch and remove the line drop.
② Tighten the line with your fingers and shake the joystick.
③ Attaching the thread to the spool disc
④ Unload the reel, clean it, and install it.
6. Maintenance
① After each fishing, the reel should be cleaned and dried.
② Regular (25 fishing trips) dismantling for maintenance, greasing of tooth discs, screw teeth, positioning teeth, sliders, rocker shafts, bearings, etc.
③ When fishing is stopped for a long time, it should be thoroughly maintained and placed in a dry place.
Previous:How to maintain fishing reels?
